Autometer 3223 Boost Line 1/8' (10ft) with Ferrules. Turbosmart Transmission Temp Gauge 0-280 F Deg 52mm - 2 1/16. AutoMeter Ultra Lite II Fuel Pressure Gauges. PPE 516010100 Tubing Kit for Boost Gauge JavaScript seems to be disabled in your browser. Aeromotive Fuel Pressure Gauge 0-100 PSI - 15633.
The 3/4″ NPT plug has a 1/2″ square in the center of it and can be removed easily with a 1/2″ drive ratchet and extention. PPE’s Boost Tubing Kit allows you to tap directly into the intake manifold to get the most accurate boost reading possible. The best one of these to use is located on the back of the engine between the fuel filter and the firewall. next locate the 3/4″ NPT pipe plug in the intake manifold.
BEST BOOST GAUGE FOR DIESEL INSTALL
The easiest way to install a boost gauge on a 24V Dodge is to first aquire a 3/4″ NPT to 1/8″ NPT reducer fitting. Boost Gauge Installation on the 24 valve Engine 1998-2002 Install the fitting and connect the hose making sure that the hose fits snug but does not pinch. Locate and remove the 1/8″ NPT pipe plug (see pic) on the driver’s side of the intake manifold.Ģ. Boost Gauge Installation Dodge Cummins Turbo Diesel 1991-1998 12 Valve (Intercooled)ġ. Install fitting and connect hose making sure hose fits snug but does not pinch. MAKE SURE TO REMOVE THE RAG from the crossover pipe and clean out any chips.ħ. Use grease on the drill and tap to allow a minimum of chips to fall into the crossover pipe.Ħ. Tap this hole with a 1/8 NPT pipe tap to accept the fitting.ĥ. Drill through the back side of the crossover pipe using a letter “R” (.399 dia) drill bit just above the turbo compressor hose joint.Ĥ. This will prevent chips from entering the engine.ģ. Remove the hose from the intake crossover pipe and push a rag well into the pipe past the point to be drilled and tapped. A hole must be drilled and tapped into the intake crossover pipe for a boost source.Ģ. Simple way to install a boost gauge in a Cummins engine.1.Fits 1998-2012 Dodge Ram Cummins 2500/3500 with either the 5.9 or 6.7L Cummins engine.This Gauge Bolt Provide easy way to hook up a new boost gauge to your Cummins engine. The 6.7L application uses the same bolt but replaces one of the 4 intake ram plenum bolts instead of the intake bolts. Might Also work on the early Cummins '94-'98.5. Will work on 5.9L/6.7L Turbo Diesel engines. Remove the bolt, replace it with our easy Boost Bolt, and you now have access to pressurized air for your Boost Gauge. If you need a way to access the pressurized intake air system in your Cummins Diesel Engine to Install a Boost Gauge Kit this bolt has a hole drilled through it that will allow you to remove one of the bolts that affixes the air intake to the cylinder head. Easy Install, No drilling/tapping necessary. The VMS Racing Hollow Boost Bolt replaces a bolt on the Intake Manifold/Horn and will allow you to use the fitting for a Boost Pressure. This is an easy, effective, and inexpensive way to install a boost gauge in your Cummins engine. My question is were do i hook the line to on engine for the boost gauge, i was thinking mabey the same line i put the boost valve but im not sure.
BEST BOOST GAUGE FOR DIESEL SERIES
VMS Racing boost bolt for the 1998-2012 Dodge Ram with the Cummins turbo diesel engines. Auto Meter Z-Series Gauges for 1989-1993 Ford 6.9L 7.3L IDI Diesel Trucks - High performance movements and understated good looks make this series a perfect choice for low-key instrumentation that. hey everyone, just bought a PPE boost valve and boost gauge for my 02 duramax.
0 kommentar(er)
